Manual Raeder

Auto mechanic online – Old cars need extra care to keep the engine durability to be used optimally. If you have a VW Beetle in 1977 we got the owner’s instructions that you can make reference to the maintenance of your car. Hint owners also intended to model, feature, as well as maintenance and repair of cars. Here you’ll find information such as: operate the car properly, fuel, lubrication, technical data, plus an explanation of how the emission controls system.

get here

Volkswagen Touareg V6 engine standard in 2005, this car started to increase the capacity of the engine from 220 hp to 240 hp. Operational navigation system will change from CD to DVD-based based on the model years later, and satellite radio is available across the board.Because this car is a new model, in line with the development of an automatic transmission system. A new model of self-dimming rear view mirror is very nice car, along with the new style 18-inch alloy wheels. get here

Service Guide Maintenance and Improvements VW T2 1962 VW Collision To make improvements on the old car, it takes the appropriate instructions to correct any parts thereof. In the service guide, you will find clues about car repairs and installations are complete. List of contents includes: model identification, front bumper, rear bumper, frame, front suspension, steering, transmission & supports, wheels & brakes, fuel system, exhaust & heater, cooling & engines, electrical & Lamp, engines, roof & rear body, glass, moldings, sliding roof.

get here

This wiring diagram can be applied for the 1996/1997 Volkswagen Jetta/ Vento TDI Model, here you can easily find this following components: Diesel direct injection system control unit, engine speed sender, air mass meter. Battery, Brake light switch, Engine speed sender, Air mass meter, front right in engine compartment, Intake manifold temperature sender, Diesel direct injection system control unit, centre in plenum chamber, Immobilizer control unit (European models) or K-line for ODB-II, Diesel direct injection system control unit, needle lift sender, modulated piston movement sender. Cruise conrol. system brake pedal switch, Modulating piston movement sender, fuse location, Dash panel insert, warning lamps, Turn signal bulb, front left, Glow period warning lamp.

Download here

Its an Air Conditioner - Heater System replacement guide and wiring diagrams for VW 1995-1996 vehicle that could applied for Cabrio, Golf, Golf III, GTI, Jetta & Jetta III. Here you’ll get explanation about the A/C heater systems and the location diagrams. Temperature flap cable adjustment, Ensure cable is connected to A/C-heater control panel and panel is installed. Remove cable sleeve retaining clip (cable sleeve is Blue). Disconnect cable from central flap lever. Adjust airflow distribution knob to defrost position.

Connect cable to central flap lever. Push lever in direction of arrow until it stops. Testing: Ensure no bubbles are present in sight glass. See Fig. 1. Connect manifold gauge set to service valves. Press A/C NORM button. Set blower motor on 2nd speed. System is okay if air temperature at center vent is less than 50øF (10øC) after one minute and system operating pressures are within specification. Removal & Installation, Discharge A/C system using approved refrigerant recovery/recycling equipment. Remove front bumper. Remove instrument panel and support bracket. See INSTRUMENT PANEL. Remove evaporator housing. Exploded View Of A/C-Heater System Components. Instrument Panels. Exploded View Of Evaporator Housing.

Download here

Its a front suspension service/repair manual for Volkswagen Passat GL that can be applied for 1998-2004 model years. Here you’ll learn step by step how to repair VW Passat GL complete with figures. Content inside: Exploded View Of Front Suspension, Identifying Vehicle Data Plate, Identifying Front Height Sensor & Link. Inspection procedures: Ball joint checking, Removing Guide Control Arm From Wheel Bearing Housing, Removing Guide Control Arm Inner Bolt, Removing & Installing Guide Control Arm Bushings, Removing & Installing Lower Control Arm Bushings, Identifying Upper Control Arm Bolts, etc. This service manual available free to download in pdf format consists of 95 pages.

Download here

Volkswagen 6 speed automatic transmission design and function book is a document covers all about the 09G/09M 6-speed automatic transmission, which installed in the following vehicles: 2005 Jetta/New Beetle, 2006 Passat, 2006 Passat. Introduction, Selector Lever: Selector Lever Positions and Operation, Selector Lever Design in 2004 Golf, Selector Lever Design in 2004 Eurovan, Ignition Key Removal Lock in 2004 Golf, Ignition Key Removal Lock in 2004 Eurovan. Transmission Design, Transmission Section 09G, Transmission Section 09G - Schematic, Planetary Gear/Shifting Elements, Torque Converter, Torque Converter Lock-Up Clutch, ATF Supply/Lubrication, Section - Automatic Transmission, Park Lock, Hydraulic Control, Torque Flow. System Overview, Example: 2004 Golf. Transmission Control Module (TCM) J217, Dynamic Shifting Program DSP, Sport Mode “S”, Emergency Running Mode,
Towing, Starter Interlock, Back-up Light, Sensors, Actuators, Solenoid Valves, Electrical Pressure Control Valves, 2004 Golf Functional Diagram, 2004 EuroVan Functional Diagram, 2004 Golf CAN Databus Connections. Self-Diagnosis, Diagnostic. Service. Special Tools. Glossary.

Download Volkswagen Automatic Transmission Design and Function

This documents will guide you how to change oil and filer on a VW New Beetel with a 1.9 TDI engines. All pictures on this document are taken from 2001 VW new Beetle with automatic transmission, if you have WV golfs or Jettas it might have slighty different from the images. Materials that you need to doing this procedure are: VW approved oil, Rags or paper towels. Latex gloves or similar disposable gloves, Oil filter (It should include two O rings), Torque wrench to tighten drain plug, Small screwdriver for engine cover caps, Oil drain pan (need to catch oil coming out), etc. Here’s the step by step instructions: With the car on the ramps, crawl under or slide under if you have a creeper and remove all torx screws that are holding the belly pan.

With the belly pan removed, I normally push it back so that it is under the front seats. Now pop the hood, if you have an engine cover, it will need to be removed. Use the small screwdriver and remove the round caps. Beetles only have two of them. Golfs and Jettas have 3 of them. With a 10mm socket, remove the nuts in the cover. ) Notice the green circles in picture below. Beetles owners, use a 10mm wrench and loosen the nut on the back end of the engine cover. (Note: it may already been loosen as most people/mechanics initially loosen it and leave it alone. If you can’t remove the cover after remove the two 10mm nuts then you need to loosen it.) Remove the cover. Beetles owners, use a 10mm wrench and loosen the nut on the back end of the engine cover. Jetta and Golf owners, there is a clip holding a black cloth-covered tubing near the back nut. Unclip the tubing. Remove the cover.
2001 VW Beetle 1.9 TDI Oil Change Instructions Download pdf

The procedure below applies to the most recent 4-pin brake light switches with the following part#s - 1J0 945 511 B, 1J0 945 511 C and 1J0 945 511 D (the most recent version - if you buy a new switch it will almost certainly be the ‘D’ version since it supercedes all previous versions). If you have an older style of brake light switch with part# 1J0 945 511 A, then the special installation procedure given below does not apply. See the procedure given at the very end of this DIY for installing this switch. Introduction, Installing the switch : Before attempting to install a new brake light switch, first make sure that the switch is in its unlocked state (as described above) AND the plunger is fully extended (approx. 1?). The bracket that holds the brake light switch is indicated by the yellow arrow in the picture below. Note that the hole in the bracket is not symmetrical and as a result, the switch can only be inserted one way. Push down the brake pedal as far as it will go. If it does not go down enough, start the car temporarily to loosen the brake pedal and then turn the car off. As always, do this procedure at your own risk. I am not responsible for any mistakes in the above procedure or those that you make while performing it.

Download pdf document

This mechanical manual could be applied for these vehicles: Volkswagen Jetta, Golf, GTI 1999, 2000. This document contain regarding information: brake pads removal and installation guide, FN 3 brake caliper, service guide, Rear Wheel brakes, disk brakes service guide, parking brake adjusting, parking brake cables removal and installation, parking brake lever components, brake pedal, assembly overview, brake pedal to brake booster, disconnecting and connecting, brake pedal, removal and installation. Contain step by step procedures with illustration, component exploded view and part list. This brake service manual available free to download in pdf format consists of 52 pages.

Download here

This is a step by step technical guide to replace timing belt and water pump for Volkswagen Passat 1998-2000 models. Time required 5-12 hours, tools needed: Torx drivers - T20, T25, T30, T45; Sockets - 6mm, 10mm, 13mm, 14mm, 16mm, 19mm, 13/16?; Hex (Allen) drivers - 5mm, 6mm, 8mm, 10mm, 14mm; Torque wrench(es) - this isn’t optional. Procedures: Bumper cover and bumper removal, Getting the radiator in service position, Timing belt removal, Water pump impeller replacement, Timing belt installation, Radiator panel repositioning and bumper cover installation, Coolant refill and final check.

Download here

Both high and low beam bulbs are H1 bulbs. This information can be found in your owner’s manual or the Bentley manual for the New Beetle. Don’t depend on the auto parts store or aftermarket suppliers’ catalogs to tell you anything different. When you take out the old bulb, it should have “H1? stamped on the metal base or etched on the glass itself. Low beam is a 55 watt bulb, and high beam is 60 watts. Before you try removing the headlight housings, check for a blown fuse first, since the headlight circuits on these cars are fused. The fuse is located on the regular fuse panel inside the car, on the left side of the dashboard behind the removable cover. Open the hood. Locate the seam between the nosepiece and the front fender (either side). Go up between the first two fender mounting bolts and look down a few inches. See a small knob sticking out at you? That is a release lever for the headlight assembly. Push in on it slightly and pull all the way up as far as the lever will go. Once you have the headlight out, pull the connector off the back of the housing and take the headlight somewhere where it is easy to work on. Put it on a pillow or something soft so you don’t risk scratching the lens.

Download Bulb Replacement

This is an in-depth DIY procedures “how to install the fog lights” for VW golf/Rabbit MkV. It covers the required material, tools and gives a step-by-step procedure. By reading this installation instruction you’ll learn about these following topics: Electrical system control module identification, Accessing the electrical system control module, Retrieving the electrical system using VAG-COM, Identifying the electrical system control module type, Material, parts and tools, Requirements for relay installation, Installation procedures, Engine compartment installation, FOG Lights Grounding, Engine Compartment Routing, Dash installation and electronic integration, Finishing, programming and testing.

Download installation manual pdf